fushun

1.3343 M2 High Speed Steel Sheet and Steel Plate

Group High Speed Tool Steel Plates
Min. Order 1 piece
Terms of Payment L/C, T/T
Update Time 2019-06-05
Item specifics
Thickness1-16mm
Width810mm max
shapeSheet, plate
Surface ConditionBlack, Smooth, Bright
Delivery CondtionCold rolled+annealed, Hot rolled+annealed

Introduction:

1.3343/M2 steel is a general purpose molybdenum high speed steel. 1.3343/M2 steel is characterized by balanced combination of abrasion resistance, toughness and good red hardness. Due to its comparatively low carbon content, 1.3343/M2 steel has an excellent combination of toughness properties and abrasion resistance when properly hardened and tempered. 1.3343/M2steel is used in a wide used for all kinds of cutting tool, knife and punch and die applications.

1.3343/M2 steel is a high speed steel suitable for cutting tools such as, twist drills, broaches, taps, milling cutters, reamers, saws, knives etc. In terms of performance, 1.3343/M2 steel is an all-round steel to be used in cutting conditions where demands for hot hardness are moderate. The term hot hardness is understood as the ability of the steel to retain its hardness even at elevated temperatures. 1.3343/M2 steel is also suitable for cold work applications, e.g. in tools for punching, forming and pressing, etc. The steel possesses an admirable combination of wear resistance and toughness and in these respects is superior to the high alloyed cold work steels.

Application:

HSS Circular Saw, Blade, Press Mould, Drills, End mill, Planer Knife, Chipper Knife, Slice Knife, Hss Square Tool Bits.

Chemical Composition:

Steel Grade

C

Si

Mn

P

S

Cr

Mo

W

V

1.3343

0.86-0.94

0.45max

0.4max

0.03max

0.030max

3.8-4.5

4.7-5.2

5.9-6.7

1.7-2.4

Size Range:

Thickness:1-16mm

Width:810mm max

Length:4000mm max 

 

Tolerance of Size:

Thickness 1.5-2.5mm with Tolerance (-0,+0.15) --Cold rolled plate

Thickness 2.55-16.0mm with Tolerance (-0,+0.25) --Hot rolled plate

 

Tolerance of Amount: Above prices are based on actual weight.

Thermal Cycling:

In order to avoid decarburization, this grade should be annealed and/or hardened in a controlled neutral atmosphere, vacuum, or neutral salt furnace environment.

1. Annealing: Heat to 1600° F, soak thoroughly at heat. Furnace cool 25° F per hour to 900° F, air cool to room temperature. Approximate annealed hardness 241 Maximum Brinell.

2. Stress Relief of Unhardened Material: Heat slowly to 1200 to 1250° F. Soak for two hours per inch of thickness at heat. Slow cool (furnace cool if possible) to room temperature.

3. Hardening:
a. Preheating: Heat slowly to 1550° F, soak thoroughly, heat to 1850° F, soak thoroughly.

b. Hardening: Soak time in the furnace varies from a few minutes to a 15 minutes, depending tool size, heat capacity of the furnace, and the size of the charge.
– Heat to 2150 to 2200° F for max. toughness and minimum distortion.
– Heat to 2250 to 2275° F for max. hardness and abrasion resistance.

c. Quenching: For full hardness, oil quench to 150-200° F. Air quench to 150° F. When quenching in hot salt maintain the quench just above the Ms temperature. After equalizing withdraw parts from the hot salt and air cooled to 150° F.

d. Tempering: Double temper is mandatory, three tempers are sometimes preferred. Soak for 2 hours per inch of thickness. Air cool to room temperature between tempers. The best tempering range for hardness, strength and toughness is 1000 to 1050° F.